Beloader Pro HID Manager (Cronus Version)
You can click the X on the right to close this box, or refresh (F5) to view it again.
Before using HID Manager, you should know that there are currently two versions of Beloader Pro. The hardware is the same but the HID software is quite different. This short guide will tell you how to tell the difference between the two, and how to upgrade them both to the very latest version.
To find out if you have the OLD or NEW versions, use Zadig 2.8 (see downloads below). Connect Beloader to your PC while holding the upgrade button (WHITE LED). Open Zadig and select Options > List all Devices and if you see PSX5ACC in the list, then you have the old version and need to use Super Manager v1.4 to program the latest 20230303.1745 firmware. If you see Beloader Pro HID FS then you have the new version and can use this HID Manager tool to program your Beloader pro.
1. Click the Connect Beloader Pro button below. If it says device not detected, you need to use Super Manager v1.4 to program firmware version 20230303.1745. If it detects it will say Beloader Pro HID FS - Paired which is the new version, so skip to Step 3.
2. After the firmware has updated with Super Manager, it is VERY important that you do the following step: Unplug the USB-C cable from the Beloader Pro, then connect it again and wait 5 seconds.
3. If HID Manager detects the Beloader, select it then click CONNECT. You should also update the 20230303.1745 firmware (even if you already programmed with Super Manager). After the firmware has updated, it is VERY important that you do the following step: Unplug the USB-C cable from the Beloader Pro, then connect it again and wait 5 seconds.
4. Get your PSN ID Secret Key here: PSN ID WIZARD
5. Get the PS5 8-Digit Link PIN by going to System > Remote Play > Link - enter the PSNID Secret Key and Link code to the HID Manager Config form and click Save.
6. Now you can connect Cronus Zen to the Beloader Pro. Make sure REMOTE PLAY is enabled in Zen Studio. Once paired to the Beloader, the Touchpad and Zen RGB LEDs will change to pink. if it doesn't tap Zen's reset button.
Beloader Pro Firmware
Zadig v2.8
Before using HID Manager, you should know that there are currently two versions of Beloader Pro. The hardware is the same but the HID software is quite different. This short guide will tell you how to tell the difference between the two, and how to upgrade them both to the very latest version.
To find out if you have the OLD or NEW versions, use Zadig 2.8 (see downloads below). Connect Beloader to your PC while holding the upgrade button (WHITE LED). Open Zadig and select Options > List all Devices and if you see PSX5ACC in the list, then you have the old version and need to use Super Manager v1.4 to program the latest 20230303.1745 firmware. If you see Beloader Pro HID FS then you have the new version and can use this HID Manager tool to program your Beloader pro.
Step by Step Instructions:
1. Click the Connect Beloader Pro button below. If it says device not detected, you need to use Super Manager v1.4 to program firmware version 20230303.1745. If it detects it will say Beloader Pro HID FS - Paired which is the new version, so skip to Step 3.
2. After the firmware has updated with Super Manager, it is VERY important that you do the following step: Unplug the USB-C cable from the Beloader Pro, then connect it again and wait 5 seconds.
3. If HID Manager detects the Beloader, select it then click CONNECT. You should also update the 20230303.1745 firmware (even if you already programmed with Super Manager). After the firmware has updated, it is VERY important that you do the following step: Unplug the USB-C cable from the Beloader Pro, then connect it again and wait 5 seconds.
4. Get your PSN ID Secret Key here: PSN ID WIZARD
5. Get the PS5 8-Digit Link PIN by going to System > Remote Play > Link - enter the PSNID Secret Key and Link code to the HID Manager Config form and click Save.
6. Now you can connect Cronus Zen to the Beloader Pro. Make sure REMOTE PLAY is enabled in Zen Studio. Once paired to the Beloader, the Touchpad and Zen RGB LEDs will change to pink. if it doesn't tap Zen's reset button.
Downloads:
Super Manager v1.4 + DriverBeloader Pro Firmware
Zadig v2.8